보유장비

XPS/UPS | X선 광전자 분광기/자외선 광전자분광기

XPS/UPS
보유장비 관련 정보
연구실/분야
모델명 ESCALAB 250XI
제조사 Thermo Fisher Scientific
담당자 임동주
연락처 052-217-4032 / [email protected]
예약 가능여부 불가능
예약단위 1hr 1일최대예약시간 12hr
예약Open(~일 전) 5일전 예약취소불가(~일 전) 2시간전
장비위치 울산광역시 울주군 언양읍 유니스트길 50, 102동 B116. 샘플 보낼주소 : 울산시 울주군 언양읍 유니스트길 50 102동 201-4호
  • Description

    의뢰 절차 및 샘플 준비((Analysis request procedure and sample preparation)
    1. 의뢰서 접수(장비의뢰, sample request 누른 후 양식 입력) 후 출력, 샘플과 함께 보낸다(시료보낼주소 참고)
    2. 샘플은 가로 세로 1cm x 1cm 정도로 자른다
    3. 파우더의 경우 1mg 이상(UPS 의 경우 powder 시료는 바람직하지 않음)
    4. 샘플명은 가급적 숫자로 표기하기 바람(숫자로 하기 싫다면 반드시 의뢰서에 각각의 샘플이름을 타이핑할것)
    5. 외부 의뢰의 경우 샘플 도착하면 상태가 '분석의뢰중' 에서 '샘플접수'로 바뀝니다. 샘플 접수된후 결과는 10-15일 후 받아볼수 있습니다.
    6. 스케줄에 맞추어 샘플을 보내고 싶다면 의뢰서 접수후 따로 메일로 스케줄 요구해 줄것을 바랍니다. 형평성 차원에서 10-15일 후에 일정을 잡게 됩니다.
    7. 외부 의뢰자의 경우 샘플 회수가 어려우니 가급적 샘플의 일부분만 보내줄것을 요청함(xps 경우 가로x 세로 : 3mm x 3mm 정도면 충분함)
    8. 1cm x 1 cm 의 샘플 크기일때 그리고 기판 포함 샘플 두께가 1mm 이하일때 8개정도의 샘플을 한꺼번에 진공속으로 넣을수 있음. 두께가 이보다 두꺼워지면 한꺼번에 2개 샘플을 넣을수 있음(UPS 샘플의 경우 가로 세로 1cm 정도 크기일 경우 8개정도 한꺼번에 넣을수 있음)
    9. 스케줄에 맞추어서 샘플 보낼때 마찬가지로 의뢰서 출력본도 함께 보낼것
    10. 앞에 언급한 측정 소요기간은 일반적인 경우에 그렇고 담당 행정업무나 다른 담당 장비에 시료가 몰릴경우 좀 더 늦춰질수 있습니다. 언급한 기간까지 만약 결과가 가지 않는다면 다시 한번 메일로 진행상황을 문의해주시면 좋겠습니다.
    11. 내부의뢰자의 결과는 항상 분석결과를 아래의 서버에 올려둡니다. 홈페이지에 완료로 표시되면 아래 사이트에서 결과를 다운 받을수 있습니다. 일반적으로는 자동으로 완료 메일이 의뢰자메일주소로 가게 되어있습니다만 어쩌다 한번씩 완료 메일을 못받았다는 사람이 있으니 참고바랍니다.
    12. 측정은 기본적으로 고진공하에서 이루어지므로 증기압을 발생하는 시료는 충분히 건조후 맡기기 바랍니다. 진공 잡을때 시간이 많이 소요되면 그에 맞추어서 장비사용료가 늘어납니다. 진공이 충분히 잡히지 않으면 측정결과 못 얻고도 사용료 청구 이루어질수 있습니다(상습적인 경우).
    13. UPS 샘플의 경우 전도성이 있고 균일한 표면을 가져야 합니다. 반도체 정도의 전도성이라면 ito 기판이나 gold 로 코팅된 평평한 기판위에 수십 nm 두께의 균일한 박막 형태로 샘플을 준비해야합니다. 적절한 두께는 샘플에 따라 다르므로 여러 두께의 샘플을 시리즈로 만들어서 찾아나가야 합니다. 그 외에도 ups 측정의 경우 샘플의 거칠기나 결정배열, 오염등에 따라 결과가 균일하게 나오지 않을 수 있으니 참고해서 의뢰해주기 바랍니다.
    14. 기본적으로 데이터 피팅과 해석은 해주지 않습니다. 샘플제조과정을 모르면 의미가 없기 때문입니다.

    http://10.24.9.32:5000/
    위치: file station/Public/touser/각지도교수이니셜로 쓰인 폴더
    결과 파일 샘플이름 참조 : file station/Public/touser/SampleName

    샘플 보낼주소 : 울산시 울주군 언양읍 유니스트길 50 102동 201-4 호

    "Analysis Request Procedure and Sample Preparation
    1. Submit request ( press '장비의뢰' or 'sample request' and enter the form) , print and send it with a sample (see the address to send the sample)
    2. The sample is cut by 1cm x 1cm wide
    3. For powder, more than 1mg
    4. The sample name will be written in a series of numbers as possible (if you don't like the number, you can typed each sample name when writing a request)
    5. In the case of external requests, when the sample arrives, the status changes from 'the loop of analysis' to 'sample reception'. The measurement period takes about 10 to 15 days after the arrival of samples.
    6. If you want to send a sample according to the schedule, please submit a request and ask for a schedule via e-mail. In terms of equity, it will be scheduled after 10-15 days.
    7. In the case of external clients, it is difficult to recover the sample, so submit only a part of the sample (horizontal x vertical: 3mm x 3mm is enough)
    8. When the sample size of 1 cm x 1 cm is the size of 16 samples can be inserted into the vacuum at once.
    9. Send a request for the client together when you send a sample according to the schedule.
    10. The requirements mentioned earlier may be delayed if the sample is driven to the administrative task or other equipment in the general case. If you don't have the results until you mentioned, please contact us again by e -mail.
    11. If the sample is not severe, the charge compensation is not good, so the results are not appropriate, so if you are likely to apply for the XPS/UPS (Escalab) equipment.
    12. The first person to commission, no matter how many samples to be requested, are asked to request a small number of samples first and receive the results, and then it is desirable to request a lot of similar samples at once. The equipment may not be satisfied with all samples. In particular, samples with little conductivity may not be able to reach the sample of the equipment.
    12. The results of the internal client always put the analysis results on the server below. When displayed on the homepage, you can download the results from the site below. In general, the completion mail is automatically going to the client's mail address, but some people have not received the completion mail once.
    13. The measurement is basically under highjin, so leave the sample that generates steam pressure and leave it. When it takes a lot of time to catch vacuum, the equipment usage will increase accordingly. If the vacuum is not enough, it may be made without the measurement as a result (habitual case).

    http://10.24.9.32:5000/
    Location: Folder used as File Station/Public/TOUSER
    See the result file sample name: File Station/Public/Touser/Samplename





    Sample Send Address: Unist-gil 502-dong 201-4, Unist-eup, Ulju-gun, Ulsan"

    X-ray photoelectron spectroscopy (XPS) is a quantitative spectroscopic technique that measures the elemental composition, empirical formula, chemical state and electronic state of the elements that exist within a material. XPS spectra are obtained by irradiating a material with a beam of aluminum or magnesium X-rays while simultaneously measuring the kinetic energy (KE) and number of electrons that escape from the top 1 to 10 nm of the material being analyzed.

  • Specifications

    • Ultra high vacuum : 1 x 10-10 torr, metal chamber

    • Hemispherical energy analyzer (High Resolution 0.45eV)

    • Energy source : monochromated Al-Kα, ultraviolet He1, He2

    • charge compensation

    • XPS imaging : Resolution 3μm

    • UPS (ultraviolet source)

  • Applications

    • Analysis of organic compound

    • Analysis of thin film

    • Depth profile

    • Work function